Applications / Insect & Rodent Traps

    Adhesives Engineered to Catch — and Hold

    Specialist pressure-sensitive adhesives for pest monitoring traps and control devices

    Formulating a pest trap adhesive is a technical tightrope act. It needs to be tacky enough to trap a 0.2mg insect, resilient enough to survive weeks of UV exposure and temperature swings, and consistent enough to coat at production speed. We've spent years perfecting that balance.

    Products for Pest Trap Manufacturing

    UV-stabilised pressure-sensitive adhesives specifically formulated for pest monitoring and control devices.

    Type:
    Format:
    Application:
    Industry:
    Equipment:
    Fastlock® 30139UV product

    Fastlock® 30139UV

    UV-stabilised pressure-sensitive hot melt for pest traps

    • Good thermal stability and long pot life for consistent application
    • Supplied in easy-to-handle PillowPacks
    • Excellent high grab for insect monitor traps.
    • Superior UV resistance for use on UV lamps and in glasshouses.
    • Approved for use with Rentokil applications.
    hot melt adhesive
    Box
    View product page
    Fastlock® 30028 UV product

    Fastlock® 30028 UV

    Specialist fly trap paste adhesive

    • Extremely high 'grab' soft paste adhesive
    • Excellent UV resistance for glasshouses
    • Very low odour
    • Low application temperature
    • Very clean application and when applied to rolls, gives even coverage on both sides when unrolled
    hot melt adhesive
    Drum
    View product page

    Showing 2 of 2 products • View all products

    Getting pest trap adhesive right is a balancing act — too hard and insects walk away, too soft and it drips off the board

    The Challenges You Face

    Pest trap adhesive formulation is deceptively complex. Here are the key technical hurdles that can make or break your product's performance.

    Getting the Right Level of Tack

    An adhesive designed for product assembly may require huge force to pull apart, yet perform terribly with the 0.2 milligrams of force exerted by a landing insect. Pest trap adhesives demand an entirely different approach to tackiness.

    Extreme Temperature Swings

    Traps are deployed in environments ranging from near-freezing to tropical temperatures above 40°C. Heat causes adhesive to drip and seep; cold makes it waxy and ineffective. Your adhesive needs to perform across the full range.

    UV Degradation

    Intense ultraviolet radiation — from the sun and from UV lamps used to attract insects — can severely degrade adhesive performance over time. Without UV stabilisation, your traps lose catching power rapidly.

    Longevity in the Field

    Pest traps must remain effective for weeks at a time through heating and cooling cycles, UV exposure, dust and debris. Performance that drops off after a few days costs you money in replacements.

    Dripping and Bleed-Through

    Paste adhesives can drip at elevated temperatures, creating mess and reducing effectiveness. Hot melt adhesives can bleed through release liners, causing unsightly blotches and sticking issues.

    Coat Weight Consistency

    Too much adhesive creates waste and allows dripping. Too little reduces catching effectiveness. Achieving a uniform, optimised coat weight across every trap is a critical production challenge.

    Why Hot Melt PSA for Pest Traps?

    Hot melt pressure-sensitive adhesives offer the ideal balance of tack, temperature resilience and production efficiency for pest trap manufacturing.

    Instant Tack on Contact

    Applied at 140–180°C, hot melt PSA develops immediate pressure-sensitive tack as it cools — no drying time, no solvents, and traps are ready to deploy straight off the line.

    Built for Extreme Conditions

    Our hot melt formulations maintain their tack from near-freezing to 40°C+ without dripping or going waxy — and UV stabilisers protect performance through weeks of sunlight and lamp exposure.

    Engineered Catch Performance

    The rheology is tuned so the adhesive surface is soft enough for a 0.2mg insect to penetrate, yet cohesive enough to hold larger crawling pests — one formulation covers flying and crawling traps.

    How We Solve These Challenges

    We don't just supply adhesive — we engineer it around your specific trap design, target pest and production process.

    Tailored Rheology

    We engineer the adhesive to be liquid enough for pest legs and wings to penetrate the surface, yet cohesive enough to hold them when they try to escape.

    UV-Stabilised Formulations

    Our formulations incorporate UV-absorbing stabilisers that protect against degradation from sunlight and insect-attracting UV lamps, maintaining catching power for weeks.

    Wide Temperature Window

    Fastlock 30139UV maintains its tack across a broad temperature range — from cold storage environments to hot greenhouses — without dripping or becoming waxy.

    Optimised for Your Process

    Whether you're coating onto board for rodent traps or film for flying insect traps, we work with you to optimise coat weights, application temperatures and line speeds.

    Trap Types We Supply

    From yellow monitoring traps in commercial greenhouses to rodent glue boards used in food processing facilities, our adhesives are formulated for the specific demands of each trap type.

    Sticky fly sheets and ribbons
    Yellow monitoring traps for greenhouses
    Rodent glue boards
    Insect monitoring stations
    UV light trap boards
    Crawling insect traps

    Every formulation is tested for tack, UV stability, temperature resistance and bleed-through

    Our in-house laboratory uses probe tack testing, SAFT analysis, UV exposure trials and bleed-through assessments to ensure your adhesive performs exactly as needed.

    Free Technical Whitepaper

    The Science Behind Sticky Pest Trap Adhesives and Pastes

    Go deeper into the formulation science — covering probe tack testing, viscosity profiles, UV degradation mechanisms, adhesive–cohesion balancing and comparison data between paste and hot melt PSA types.

    • Probe tack test data and interpretation
    • Paste vs hot melt PSA comparison table
    • UV stability and bleed-through testing methods
    • Viscosity curves for paste and hot melt grades
    Download the Whitepaper

    Need an Adhesive That Actually Catches?

    Whether you're manufacturing sticky fly sheets, rodent glue boards or monitoring traps, we'll work with you to develop an adhesive that performs — in the lab and in the field. Get in touch for a no-obligation technical discussion.

    Request Samples, MSDS & Technical Data Sheets

    Select the products you're interested in and we'll send you the information you need.